12.12.2017

Поиск по сайту

 

  603950, Нижний Новгород, ул. Минина, д.24 Официальная почта: nntu@nntu.ru Факс: +7 (831) 436 94 75     English Instagram Нижегородского государственного технического университета им. Р.Е. АлексееваОфициальная группа ВКонтакте Нижегородского государственного технического университета им. Р.Е. АлексееваNizhny Novgorod State Technical UniversityТелеграмм-канал Нижегородского государственного технического университета им. Р.Е. Алексеева

Transactions of NNSTU #5, 2014. Contents

Name of Article Page File
NUCLEAR POWER ENGINEERING AND APPLIED PHYSICS 13
Anoshkin Y.I., Zhilov D.M., Kutsenko K.V.
On the issue of method of accounting analysis of temperature condition of fuel element of reactor core in area of wall boiling of water coolant
13
Beznosov A.V., Bokov P.A., Novozhilova O.O., Bokova T.A., Soloviev A.O.
Problems of regulation melt temperature of lead on the experimental stand FT-4 NSTU
18
Beznosov A.V., Bokov P.A., Zudin A.D., Lvov A.V., Bokova T.A., Trushkov N.D.
Hydrodynamics and performance of model the main circulation pump brest-od-300 lead coolant on bench FT-4 NNSTU
25
Mihalitsyn E.A., Kozhevnikova T.V.
The adaptation of differential equations contrac-tion method to solving boundary value problems about shielded circular homogeneous ferrite loaded cavity
39
Lvov A.E., Rudoyasova L.G., Shishkov G.I., Sherbakov V.V.
Thin-film strip attenuators
40
Varentsov A.V., Solntsev D.N. , Sorokin V.D., Legchanov M.A., Khrobostov A.E.
Experimental researches of mass exchange of heat-carrier flow in fuil asemblies of the KLT-40S and RITM-200 reactors
47
LAND-BASED TRANSPORT SYSTEMS 52
Teslenko D.S., Belyakov V.V., Makarov V.S., Zezyulin D.V.
Using finite-element method for solving terramechanics tasks
52
ELECTRICAL ENGINEERING AND POWER INDUSTRY 59
Daryenkov A.B., Vorotyncev I.V., Varygin I.A.
Modelling and simulation of three phase matrix converter fed induction motor drive
59
Kolosov R.V., Titov V.G., Maksimov Yu.M.
Control system for autonomous group of renewable energy sources
65
Kralin A.A., Vorotyncev I.V., Gulyaev V.V.
Research of parallel operation of three-phase transformers with y/y0 windings connection at phase by phase regulation
70
Vagin G. Ya., Solntsev Е.В., Shevchenko A. S., Malafeev O. Yu.
Methodology of the illuminants economic ranking based on total cost of ownership
75
Lapaev D.N., Mochalin D.S., Titov V.G.
Direction of the air cooled heat exchanger of gas on the compressor station
79
Lomakina L.S., Sadikov D.G., Titov V.G.
Energy efficient speed drive gas pumping unit
84
Smirnov A.Y., Kralin A.A., Zimin A.Y., Husnunts-Krieger T.N.
Improvement of electromechanical transducers for vertical movement regulators
92
Sosnina E.N., Kechkin A.Y., Filatov D.A.
Questions power supply consumers removed from network infrastructure
100
Grebenshikov V.I., Chivenkov A.I., Sevastyanov V.V., Zakharov I.A.
Development of control systems of intelligent controllers electrical energy quality parameters
106
MECHANICAL ENGINEERING AND AUTOMATION
PROCEEDINGS OF THE REGIONAL YOUTH SCIENTIFIC AND PRACTICAL CONFERENCE "Quality MANAGEMENT SYSTEM IN MACHINEBUILDING. IMPROVING PRODUCTS COMPETITIVENESS"
(N. Novgorod: NSTU n.a. R.Y. Alexeev, 10-11 december 2014)
112
Liamkin G.L., Steshov V.V.
Research of heat-exchange rate when cooling the inner surface of a hot metal pipe with air-and-water drip jets
112
Steshov V.V., Liamkin G.L.
Experimental development of an internal cooling system of a medium-caliber artillery barrel
117
Bukhnin A. V., Volkova I.E., Kalashnikova A.G.
A microcontroller based device for password generation and entering
122
Steshov V.V., Zhadnov P.S.
Adaptation of a compressor to operation in a transport mount with regard for wide ambient temperature range
127
Steshov V.V.
Compressed air dehumidifying systems for sph pneumatic-transporting automatic loader
131
Bebenin A.N., Zotov A.V., Shiryaev S.V.
System of actions directed on providing de-termination of functioning parameters of complicate technical systems during tests
134
Volkova I.E., Sokolova J.V.
Optimization of depth diagnosis of the complex system, based on weight coefficients in its subsystems
139
Bebenin A.N., Rudy V.I., Yankitova I.A., Litovchenko V. N., Vorobyov R.A., Karnavskaya T.G.
Investigation of mechanical properties of the protective refractory coat-ing applied by the method of ion-plasma vacuum magnetron sputtering
143
Shvetsov A. V., Lozhkin A. A., Juhnowski I. A., Khairulin R.R., Benson V.V., Bebenin A. N., Volkova I.E.
Prediction of target motion by data of an optical tracking system
147
Bebenin A.N., Zotov A.V., Shiryaev S.V.
Identification of difficult to diagnostic refusals of functional subsystems mechatronic complexes
151
Slutsky V.E., Zaycev A.A.
Accounting for deformations of the rotating band during firing in the ballistic preparation of artillery systems
154
Slutsky V.E., Zaycev A.A.
On procedures of handling the ballistic preparation of artillery systems by applying the equipment of the check & test vehicle
160
Volkov A.S., Volkova I.E., Zemskov P.A.
Combined method of leak detection in pipeline
166
Sokolova E.S., Volkova I.E., Timofeeva O.P., Kadilenko E.S.
Peculiarities of control system software for unmanned vehicles
171
Volkova I.E., Shagalova P.A., Lyakhmanov D.F.
Development of the multi-step-ahead forecasting system based on the multilayer artificial neural network
175
Laptev I.L., Lapteva Е.А.
Increasing effectiveness of chisel functioning
179
Malikov N.Sh., Slutsky V.Ef.
3D model for research on interaction dynamics withing "gun-tube-shot" system for the shooting accuracy tasks solution
184
Gavrilyuk E.A., Mantserov S.A., Sinichkin S.G.
The methods of evaluation of technical condition of automatic systems of gas compressor units operational control/a>
191
Schyekin A. M., Kulikova E. A.
Software module for product information model creation
195
Schyekin A.M., Kulikova E.A., Kochin A.N.
Optimization of parameters of lever mechanisms of machine retaining devices
200
Steshov V.V.
Developmental testing of the processes of conveying artillery round elements in the pneumatic-transporting automatic loader of an artillery gun
205
Koshelev O.S., Magnitskaya S.F.
Some issues of diagnostics of machines
208
Petrovskiy A.N., Druzhinin G. A.
Special aspects of two-position gear hobbing
213
Trofimova M.S.
APQP process as an instrument for domestic autocomponents manu-facturers and suppliers development
220
Kraynov V.V.
Burnishing effectiveness in copper (waveguiding) pieces
225
Baleyev B.F.
Self-sustained oscillations of calender roll sets
230
Zhilin P.L., Konishchev B.P., Lebedev S.A.
Resarch on quality improvement of со2-shielded welding with an additional cold filler
235
Derbenev A.A.
The method of forecasting indicators of strain hardening of the metal in the process of cold heading fasteners
238
Koshelev O. S., Ivanov S. V., Chesnokov E. V.
Analysis of the methods used for shell production
243
Trofimova M. S., Trofimov S. M.
Research on the effectiveness of tpm and smed lean production tools exemplified by "feintool" pressure machine (die) set up operator
247
Mezentseva E. A., Kretinin O. V.
Studies of the automated system of quality evaluation of technical disciplines material
250
Shabarov R. A., Kretinin O. V.
Study of the data exchange process between different automated systems
255
Ershov V.N., Ershov N.V.
Impact effect on complex systems
261
Serov A.S., Mantserov S. A., Sinichkin S. G., Maksimov V. Yu.
Automated work station of a verification officer for adjustable electric resistance measures
265
Kretinin O. V., Sizov A. Yu., Tumanov A. A., Fedossova L. O.
Automated system for structural and parametrical models optimization upon technical and economic criteria in virtual environment
271
Khadeev R. G., Sinichkin S. G., Mantserov S. A., Maksimov V. Yu.
Model development of direct current voltage dividers verification process
276
Kalyashina A.V., Kretinin O. V., Sizov A. Yu., Tumanov A. A., Fedossova L. O.
Development of a robotic system construction for extended closed small diameter objects diagnostics in autodesk inventor environment using automated optimization systemи
282
Stepanov K. V., Fedossova L. O.
"Ni labview robotics starter kit" robotic platform and its use in the teaching process
286
Kuvshinova N. N.
The possibility of aluminothermic process application in centre die casting
291
Kuvshinova N. N.
Fields of development of exothermic weld overlaying
296
Tikhonova N. E.
Optimizing of the basic elements and shell architecture of an icebreaker depending on the ice conditions
302
Polynin G. E.
Forming first year students contingent in the university and some ways of problem solution
309
Ustinov B.V., Grishin E.N., Aushev A.A., Mal'tsev I.M.
Research of influence physical-treatment of speed electrothermal processing by current of high density on the struc-ture and properties of 8H6NFТ tools steel
317
Pryguin A. A., Zimina E.V., Kaynova V. N.
Measuring system analysis basing on a coordinate inspection station
327
Bespalov V. V.
Engineering support of the quality of the machines
334
Metelyov B. A.
Development of the basic notions of the elements of the technological machining process
339
Ivanov A.A.
Optimal schedules of parallel and consecutive processing of pieces without changeover
346
Schneiberg А. M., Mikhalenko F. P.
Cumulative deformation at combined upset-torsion loading
351
Shestopyorov V. Yu.
Damage (failure) and evaluation of durability of constructive ele-ments operating in cavitating liquids
361
Smolenskiy S.Yu., Podnozov V.G.
T joints forming under spin welding
366
Vavilov Yu. N., Skobeleva I. Yu.
Load gripper for glass-bending furnaces
372
Kiryushov D.P., Kvartalov A. R.
New options of AUTODESK INVENTOR 2015
376
Zhilin P. L., Konischev B. P., Lebedev S. A.
Resarch on productivity increase and quality improvement of со2-shielded welding with an additional cold filler
381
Kvartalov A.R., Moskvichyov A. A.
Device for automated cutting tools setting on a turning machine
388
Zimin M. N., Kanevskiy G. N., Korevskiy O. A., Pichuguin A. S.
Automated integrated process of milling and engraving work
394
Volnov O. I., Dudukin D. O.
Fiber glass plastic. History of development, production technology, product shaping and current usage
400
Zaporozhtsev A.V.
Case management in maintenance and repair of complex equipment systems
405
Kalyashina A.V., Berdichevskiy R.B.
Programmed optimization of working operations exemplified by mechatronic complex by "FESTO"
411
Kalyashina A.V., Tsybushkina M. M.
Inventor api and iLogic functional options analysis for the purpose of their usage in the course of the teaching process of a technical university
416
Kalyashina А.V., Kocherov A. V.
Application of the fuzzy control algorithm in aluminum sulfate production
421
Kozlov I. K., Syrotkin D. G.
Studies and developments in the field of anodic welding
426
Kozlov I. K., Alekseev V. A.
Welded medical instrument of titanium alloys production technology optimization
432
Kuznetsov S.V.
Influence of cross-section forces on quality of the details received by methods of a sheet-metal forming/a>
438
Kuznetsov S.V.
Technique of experimental definition of cross-section forces depending on conditions of their holding for metal forming operations
443
Kuznetsov S.V.
Technique of theoretical definition of cross-section forces depending on conditions of their holding for metal forming operations
448

Главный редактор
Ректор НГТУ С.М. Дмитриев
Адрес редакции:
603950 Нижний Новгород, ул. Минина, 24, ауд. 1363–3
тел.: +7 (831) 436–21–10
e-mail: rsl@nntu.ru


Свидетельство о регистрации
периодического печатного издания:
ПИ № ФС 77-56417